Embedded Networking

Nowadays everything and anything are connected using Internet Protocols: TCP, UDP, RTP, ARP, IGMP... the list goes on and on. However, embedded systems are frequently island systems, that are not connected to the usual support services such as DHCP and DNS. IP addresses are static and there are no gateways to other nets.

Island Networks

When you plug an office laptop computer into a typical embedded net, nothing happens, your machine remains unconfigured and you cannot access anything. Testing and debugging a modern system therefore requires a little bit of advanced networking knowledge.

In order to communicate on a net, your machine needs at least two things to be configured: IP Address and Subnet Mask, but before you can set it, you first have to disable the NetworkManager auto-configuration utility, since in an embedded system, it is more of a hindrance than a help.

Each time you unplug a cable or power down the device your laptop computer is connected to, Network Manager tends to forget the IP settings and when you replug it, you got to set everything up all over again. This gets annoying super quick.

Network Manager

To save your sanity, disable NetworkManager with one of these commands:
# service NetworkManager stop

or
# systemctl stop NetworkManager.service
# systemctl disable NetworkManager.service

or
# killall NetworkManager

Network Settings

Once NetworkManager is truly dead, see what the available network devices are:

# ifconfig

# ip link show

Now you can set a static address and be assured that it will stick:

# ifconfig em1 192.168.111.1 netmask 255.255.255.0 up

# ip addr add 192.168.111.1/24 dev em1

# ip link set em1 up

There Is More Than One Way To Do It (TIMTOWDI).

Going back to Normal

When you need to check you email or do a search for information and you need to plug the machine back into a wall socket, you got to restart the network, or just restart Network Manager.

# systemctl restart network.service

# systemctl restart NetworkManager.service

Happy debugging!

Comments

PCB Mill

PCB Mill Kit My latest toy is a small PCB Mill, a CNC 3018 Pro, there are many available from Ali Express for the enormous sum of 285 Dirhams or so, which is about 70 Euro. I thought that even if it didn't work at all, it would not be a big loss. Assembled CNC 3018 Kit It will help if you have a little previous workshop experience, but these machines are so simple and relatively slow moving, that any radio-geek can safely experiment. Carving With a V-bit in a Puddle of Oil Of course I can have boards made in China by Dirty PCBs , but what is the fun in that? The problem with making PCB antennas, is that you need to experiment to change the design 1 mm this way or that, to tune it just so and just such and having to wait 2 weeks for each experiment doesn't work. A few hours playing with a router is more practical. It turned out to be a pretty nice little kit, made from aluminium and 1/4 inch Bakelite (paper reinforced phenol formaldehyde). This Pre...

Yagi Antenna for 900 MHz ISM Band

I like tinkering with wire antenna designs, since they are simple and cheap to make. Mr Yagi invented his antenna about 100 years ago, but there are still some things left to learn about it. 900 MHz ISM Band Yagi The 900 MHz ISM band ranges from 902 to 928 MHz. Covering the whole band with a single Yagi antenna is difficult, since they are inherently narrow band devices. Consequently some tweaking is required and the result below is a desensitized design that can be built and replicated quite easily, but you need a network analyzer - "To Measure, is to Know!" A Yagi generally consists of a Reflector, Radiator and one or more Director elements, arranged on a boom. For a small Yagi, a wooden ruler works a treat, since one can easily mark the position of the wires. The wire elements are fastened to the bottom of the ruler with hot glue. The wire elements are made from straightened out jumbo size paper clips. The balun, is tw...

OpenEMS with Octave and SciLAB

I wanted to do some advanced RF antenna development work and needed an electromagnetic field solver that is a bit more up to date than NEC2 . Commercial solvers from Matlab , Ansys and others are hideously expensive (in the order of $20,000 to $50,000) and do not fit in the wallet of a hobbyist or a small consulting company. Recently, openEMS became available and it fills the niche with a capable free tool. In general, openEMS is a solver - a Finite-Difference Time-Domain (FDTD) numerical engine. You interact with it through Octave , which is almost identical to Matlab . You can watch a good video by Thorsten Liebig here: https://www.youtube.com/watch?app=desktop&v=ThMLf0d5gaE Getting it to work is a little painful, but it is free, so bear with it - then save a backup clone, or a zipped copy of the whole virtual machine directory and NEVER update it, to ensure that it keeps going and doesn't get broken by future updates, right when you are ...

Aeronetworks sro - Airborne Linux

Search This Blog