Skip to main content

CRCs and Serial Ports


Scope

This mini guide explains how to append messages with CRCs and send them to a serial port.  Operating a serial port from the Linux Bash shell is very obscure and precious few people know how to do it.

Once you know the tricks, it is extremely powerful and a big time saver over the more complicated and error prone alternatives.

Also see this: http://www.aeronetworks.ca/2014/07/fletcher-checksum-calculator-in-bash.html

Get a set of CRC utilities from here:

http://www.hampa.ch/misc-utils/index.html
http://www.hampa.ch/misc-utils/misc-utils-0.2.2.tar.gz

Install the tools:
$ cd
$ mkdir misc
$ cd misc
$ wget http://www.hampa.ch/misc-utils/misc-utils-0.2.2.tar.gz
$ tar -zxvf misc-utils-0.2.2.tar.gz
$ ./configure
$ make
$ su
password
# make install

CRC Message Preparation:

Prepare a message step by step:
$ echo -en "\xa5\x10\x01\xca" > msg
$ hex msg
A5 10 01 CA # 00000000  ....
$ crc -g crc16 msg
41cf

Or modify the message file on the fly:
$ crc -b -g crc16 msg >> msg
$ hex msg
A5 10 01 CA 41 CF # 00000000  ....A.

Or do it all in one line:
$  echo -en "\xa5\x10\x01\xca" | crc -b -g crc16 - >> msg

Serial Port Tricks

Set the serial port in raw mode and configure it:
# stty -F /dev/ttyUSB0 raw
# stty -F /dev/ttyUSB0 19200

Prepare a message with a CRC16 and send it straight to the serial port:
$  echo -en "\xa5\x10\x01\xca" | crc -b -g crc16 - >> /dev/ttyUSB0
Labels:

Comments

Post a Comment

On topic comments are welcome. Junk will be deleted.

Popular posts from this blog

OpenEMS with Octave and SciLAB

I wanted to do some advanced RF antenna development work and needed an electromagnetic field solver that is a bit more up to date than NEC2 .  Commercial solvers from Matlab , Ansys and others are hideously expensive (in the order of $20,000 to $50,000) and do not fit in the wallet of a hobbyist or a small consulting company.  Recently, openEMS became available and it fills the niche with a capable free tool.  In general, openEMS is a solver - a Finite-Difference Time-Domain (FDTD) numerical engine.  You interact with it through Octave , which is almost identical to Matlab .  You can watch a good video by Thorsten Liebig here: https://www.youtube.com/watch?app=desktop&v=ThMLf0d5gaE   Getting it to work is a little painful, but it is free, so bear with it - then save a backup clone, or a zipped copy of the whole virtual machine directory and NEVER update it, to ensure that it keeps going and doesn't get broken by future updates, right when you are ...
Post a Comment
Read more

Parasitic Quadrifilar Helical Antenna

This article was reprinted in OSCAR News, March 2018:  http://www.amsat-uk.org If you want to receive Satellite Weather Pictures , then you need a decent antenna, otherwise you will receive more noise than picture. For polar orbit satellites, one needs an antenna with a mushroom shaped radiation pattern .  It needs to have strong gain towards the horizon where the satellites are distant, less gain upwards where they are close and as little as possible downwards, which would be wasted and a source of noise.  Most satellites are spin stabilized and therefore the antenna also needs circular polarization, otherwise the received signal will flutter as the antennas rotate through nulls. The helical antenna, first proposed by Kraus in 1948, is the natural solution to circular polarized satellite communications.  It is a simple twisted wire - there seems to be nothing to it.  Various papers have been published on helix antennas, so the operation is pretty well ...
3 comments
Read more

Yagi Antenna for 900 MHz ISM Band

I like tinkering with wire antenna designs, since they are simple and cheap to make.  Mr Yagi invented his antenna about 100 years ago, but there are still some things left to learn about it. 900 MHz ISM Band Yagi The 900 MHz ISM band ranges from 902 to 928 MHz.  Covering the whole band with a single Yagi antenna is difficult, since they are inherently narrow band devices.  Consequently some tweaking is required and the result below is a desensitized design that can be built and replicated quite easily, but you need a network analyzer - "To Measure, is to Know!" A Yagi generally consists of a Reflector, Radiator and one or more Director elements, arranged on a boom.  For a small Yagi, a wooden ruler works a treat, since one can easily mark the position of the wires.  The wire elements are fastened to the bottom of the ruler with hot glue.  The wire elements are  made from straightened out jumbo size paper clips.  The balun, is tw...
Post a Comment
Read more