Skip to main content


Simple Table Saw

To me, much of the fun of woodworking is making my own tools and jigs and then using them in a project.  Jigs made of wood do not last very long, since they either wear out, or warp (or both!), so making new jigs is a constant process.  The trick is to keep it simple, so that any worn or damaged guide piece can be replaced quickly with whatever is in your scrap wood bin.

Table Saw With Guide

When machining large pieces of wood, it is best to keep the wood still and move the machine, so a hand circular saw is a must have.  However, when working small pieces of wood, it is best to keep the machine still and move the wood, so a table saw is also a must have.  A table saw can however be rather expensive and a cheap, inaccurate, wobbly one, costs 3 times more than a hand tool.

Table Saw Saw Guide

Making your own table saw with an upside down hand saw is not difficult and it also has some advantages, notably that cutting through the table results in a zero clearance blade slot, which helps to reduce tear-out.  I set the blade to 90 degrees and leaves it that way.  I never cut at an angle with a circular saw, since it much increases the danger of a jam and kickback, which can hurt very badly.  I rather use a jigsaw for fancy cuts.

When selecting a circular saw, compare the different models on display and select the one with the sturdiest guide plate chassis.  The biggest problem with DIY tools is wobble.  Makita saws are very sturdy, while my other cheap American saw is rather wobbly, so I learned from the experience.

I made an Ikea scrap wood MDF box with a top and no bottom, to house the saw.  To adjust the blade height, I tip the box up to get to the lever and since there is no bottom, saw dust falls out and doesn't build up in the box.  However, it is a good idea to cut a hole in the side for a vacuum cleaner nozzle, to reduce the dust flying up into the air.


Upside Down Table Saw

When using the table saw, I clamp a piece of wood to the back of my work table, to keep the saw box from sliding off.   That works well enough.

Simple Saw Guides

The top overhangs the sides of the box by 5 cm, to enable the use of simple guide blocks and clamps.

The saw rip guide (Yankees call it a fence) slides along the front side, wraps around the table edge and clamps in place.  The guide ends at the middle of the blade.  At that point, the wood is cut, a longer guide doesn't help anymore and could cause the wood to jam between the guide and the blade and get flung back at high speed, which will hurt badly, so I keep the guide short.  American table saws have guides that go all the way to the back of the table - that is not a good idea.   

When you make the rip guide, glue the pieces, then clamp them to the blade and the front edge of the table.  By doing that, the guide is guaranteed to be perfectly parallel to the blade, even if the table edge is not. Once the glue set, you can add a couple of screws if needed.

Yootoob is full of fancy saw guide designs.  If you make a fancy guide, then when it breaks and/or warps, you need to spend a lot of time making a new one.  So I keep it simple, don't make fancy sliding slots in the table top and use a G clamp to secure my saw guides to the table edges.  A saw guide could be as simple as a piece of junk wood that was lying around, or a plastic rafter square.

To use a saw rip guide, clamp it lightly with a G clamp to the table edge and adjust it with a rubber mallet, then tighten the clamp.

I cut with the blade set much higher than the wood thickness.  This directs the cutting force mostly into the table and not at me, which reduces splintering and also reduces dangerous fly-back of wood pieces. It is a good idea to use a smaller size circular saw (a 5 to 7 inch blade is enough) with less power.  You will never be sorry if your puny little 5 inch table saw jams and stalls - while you will be very sorry for yourself if your saw goes Whump! and throws the wood piece back to you at 100 miles an hour.   

A ten inch table saw is a killer - A bigger table saw isn't better! 

Table Saw Cross Cut / Mitre Jig

A table saw cross cut sled is very useful.  I made one from scrap wood, that fits over the table saw box, guided by the edges.  

Table Saw Cross Cut Jig

When you glue up such a jig, put two layers of masking tape on the edges, to ensure that after you glued it, it will not stick to the table and there will be enough clearance to slide smoothly when you remove the tape.  Some wax will also help to make it move and keep it from warping as soon as you want to use it.

For miter cuts, I clamp a triangle to it.  For multiple cut offs, I use a G clamp with a stop block.

Hand Saw Cross Cut Sled 

Another jig I use a lot, is a cross cut sled for my hand saw.  The guide rails are left over oak edging.  Put some wax on them.

Cross Cut Sled

If I need a 45 degree cut, I simply clamp a plastic rafter square to the base.  Don't ever use a steel square as a cutting guide.  I would not like to accidentally cut into a steel square - the result of tungsten saw teeth binding into a steel tool won't be fun at all.  This sled has seen heavy use over the past year.

The Simplest Jigsaw Guide Ever

There are many videos on Yootoob showing how to turn a jigsaw with a long flexible blade into something resembling a band saw, by using a wooden overhead arm and ball bearings.  You don't need any of that.   

Simply buy Professional quality blades. It is the same type of blade you always buy, but with a P at the end of the part number.  Those blades are thick and stiff.  They don't flex and they cut straight!

Jig Saw with Dust Port and Professional Blade

Here is a picture of my little jigsaw, with a professional blade and a conical PVC rubber adaptor for the little 21 mm dust port to fit a vacuum cleaner hose.  You can get the conical widgets on Amazon in packs of 2 to 5.  Do yourself a favour and buy a bunch of them.

La voila



Popular posts from this blog

Parasitic Quadrifilar Helical Antenna

This article was reprinted in OSCAR News, March 2018: If you want to receive Satellite Weather Pictures , then you need a decent antenna, otherwise you will receive more noise than picture. For polar orbit satellites, one needs an antenna with a mushroom shaped radiation pattern .  It needs to have strong gain towards the horizon where the satellites are distant, less gain upwards where they are close and as little as possible downwards, which would be wasted and a source of noise.  Most satellites are spin stabilized and therefore the antenna also needs circular polarization, otherwise the received signal will flutter as the antennas rotate through nulls. The helical antenna, first proposed by Kraus in 1948, is the natural solution to circular polarized satellite communications.  It is a simple twisted wire - there seems to be nothing to it.  Various papers have been published on helix antennas, so the operation is pretty well understood. Therefore,

Weather Satellite Turnstile Antennas for the 2 meter Band

NEC2, 2 m band, 146 MHz, Yagi Turnstile Simulation and Build This article describes a Turnstile Antenna for the 2 meter band, 146 MHz amateur satcom, 137 MHz NOAA and Russian Meteor weather satellites.  Weather satellite reception is described here .  A quadrifilar helical antenna is described here .   Engineering, is the art of making what you need,  from what you can get. Radiation Pattern of the Three Element Yagi-Uda Antenna Once one combine and cross two Yagis, the pattern becomes distinctly twisted. The right hand polarization actually becomes visible in the radiation pattern plot, which I found really cool. Radiation Pattern of Six Element Turnstile Antenna Only a true RF Geek can appreciate the twisted invisible inner beauty of a herring bone antenna... Six Element Turnstile Antenna Essentially, it is three crosses on a stick.  The driven elements are broken in the middle at the drive points.  The other elements can go straight throug

To C or not to C, That is the Question

As most would know, the Kernighan and Ritchie C Programming Language is an improved version of B, which is a simplified version of BCPL, which is derived from ALGOL, which is the Ur computer language that started the whole madness, when Adam needed an operating system for his Abacus, to count Eve's apples in the garden of Eden in Iraq.  The result is that C is my favourite, most hated computer language , which I use for everything. At university, I learned FORTRAN with punch cards on a Sperry-Univac, in order to run SPICE, to simulate an operational amplifier.  Computers rapidly lost their glamour after that era! Nobody taught me C.  I bought the book and figured it out myself. Over time, I wrote a couple of assemblers, a linker-locator, various low level debuggers and schedulers and I even fixed a bug in a C compiler - not because I wanted to, but because I had to, to get the job done!   Much of my software work was down in the weeds with DSP and radio modems ( Synchronization,