Skip to main content

GI-7b Microwave Triode

I recently obtained an ancient Rusky GI-7b microwave C-band triode.  Packed in an innocent looking styrofoam container (I didn't know they had styrofoam in the bronze age - maybe that is how they floated the pyramid stones down the Nile!), it is quite a monster:

GI-7b Radar Amplifier Triode

This is a radar amplifier tube designed to operate while pulsing at up to 9 kV and 3 GHz.

To digress a bit, contrary to common perception, there are still lots of microwave electron tubes in use,  for example microwave ovens, radars, medical diagnostic equipment and satellites.  Travelling Wave Tubes are popular in satellite transmitters, because they are very efficient, very rugged and small. TWT amplifiers have been manufactured by the likes of Honeywell, Thales and others for over half a century - the frequency band just keeps going up and they now operate in the Ka band: https://aerospace.honeywell.com/en/learn/products/satellite-communications/traveling-wave-tube-amplifiers

What I would like to do one day, is build a Thermionic Valve satcom UHF preamplifier for use with a SATNOGS  Raspberry Pi earth observation ground station - just for fun.  I got some small Nuvistor tubes for that.

Really BIG electron tubes and oscillators are made in China by the Bejing Jenerator Co:  https://jenerator.en.ecplaza.net

There is also still a manufacturor of new electron tubes for audio amplifiers, the Xpo-Pul (Reflektor) factory in Saratov, Russia:   http://rutubes.com/category/reflector-tube-saratov-russia/

The big GI-7 tube is supposed to have a vacuum inside - I hope it is still in there and that it didn't crawl out through a crack in the casing - it was designed for use in a battle tank, so it should be OK!

Serious Data Sheet

The Heater and Cathode are at the bottom, the Gate in the middle and the Anode at the top.  It is wired like a simpe Triode - no confusing extra grids as in a Pentode.  I frequently wondered whether the extra grids of a Pentode really do anything useful, or are just there for marketing purposes.  Hey, five are better than three right?

Electron Tubes tend to be very forgiving things and like a little kitten, will usually try their best to please you, if you warm them up nice and cozy and feed them some lecce.  Therefore I'm wondering how it will do at a more pedestrian 335 VDC at 10 kHz baseband, in an audio amplifier output stage.  The biggest problem will likely be the 12 V, 2 A heater current - 24 Watt to do mostly nothing - maybe it will work at half that.

One should not run a tube at kilovolts in your living room anyway, since you can get X-rays and Ozone, which are both not very nice.

Some Audiophile amplifiers have a random tube or two on display and wired such that if you remove the tube, the amp stops working, while it actually doesn't do anything at all, but since I grew up with tube fired radars in the Army, I'll find a way to make it work for real!


Crazy Socket

The socket for this valve is total overkill, so I'll have to make something more aesthetically pleasing.

UHF and Microwave Ceramic Valves are usually quite easy to solder to, since the contacts are silver plated.  So I can run some copper steam tubes around the valve just for show: 

RG405/U - https://www.pasternack.com/semirigid-0.085-rg405-50-ohm-coax-cable-copper-rg405-u-p.aspx

Semi-rigid coax make nice looking steam tubes and shield the signals from 5G Audiophile interference, so you don't need a double layer tin-foil hat when you listen to my amps. https://www.aeronetworks.ca/2015/02/cool-amplifier.html

Here is the complete thermionic valve data sheet:




GI-7b Triode

Microamp per kilovolt - Hmmm...  Keep yer kotton picken fingers in yer pokkets!

What I want to do is far off the left-hand bottom end of all the curves, but it should work anyway.


For now, it will have to rest some more in my Junque Bochs.  

Maybe I'll get to it next year. 

No rush.

The tube patiently waited 50 years already, so it can wait some more!


La voila,

H


Labels:

Comments

Post a Comment

On topic comments are welcome. Junk will be deleted.

Popular posts from this blog

Parasitic Quadrifilar Helical Antenna

This article was reprinted in OSCAR News, March 2018:  http://www.amsat-uk.org If you want to receive Satellite Weather Pictures , then you need a decent antenna, otherwise you will receive more noise than picture. For polar orbit satellites, one needs an antenna with a mushroom shaped radiation pattern .  It needs to have strong gain towards the horizon where the satellites are distant, less gain upwards where they are close and as little as possible downwards, which would be wasted and a source of noise.  Most satellites are spin stabilized and therefore the antenna also needs circular polarization, otherwise the received signal will flutter as the antennas rotate through nulls. The helical antenna, first proposed by Kraus in 1948, is the natural solution to circular polarized satellite communications.  It is a simple twisted wire - there seems to be nothing to it.  Various papers have been published on helix antennas, so the operation is pretty well understood. Therefore,
Post a Comment
Read more

Weather Satellite Turnstile Antennas for the 2 meter Band

NEC2, 2 m band, 146 MHz, Yagi Turnstile Simulation and Build This article describes a Turnstile Antenna for the 2 meter band, 146 MHz amateur satcom, 137 MHz NOAA and Russian Meteor weather satellites.  Weather satellite reception is described here .  A quadrifilar helical antenna is described here .   Engineering, is the art of making what you need,  from what you can get. Radiation Pattern of the Three Element Yagi-Uda Antenna Once one combine and cross two Yagis, the pattern becomes distinctly twisted. The right hand polarization actually becomes visible in the radiation pattern plot, which I found really cool. Radiation Pattern of Six Element Turnstile Antenna Only a true RF Geek can appreciate the twisted invisible inner beauty of a herring bone antenna... Six Element Turnstile Antenna Essentially, it is three crosses on a stick.  The driven elements are broken in the middle at the drive points.  The other elements can go straight throug
Post a Comment
Read more

Patch Antenna Design with NEC2

The older free Numerical Electromagnetic Code version 2 (NEC2) from Lawrence Livermore Lab assumes an air dielectric.  This makes it hard (but not impossible) for a radio amateur to experiment with Printed Circuit Board Patch antennas and micro strip lines. Air Spaced Patch Antenna Radiation Pattern You could use the free ASAP simulation program , which handles thin dielectrics, you could shell out a few hundred Dollars for a copy of NEC4 , You could buy GEMACS if you live in the USA, or you could add distributed capacitors to a NEC2 model with LD cards (hook up one capacitor in the middle of each element.), but that is far too much money/trouble for most. More information on driving an array antenna can be found here: https://www.aeronetworks.ca/2019/03/driving-quad-patch-array-antenna.htm l Air Dielectric Patch   The obvious lazy solution is to accept the limitation and make an air dielectric patch antenna. An advantage of using air dielectric, is that the antenn
3 comments
Read more