Open Sourcery

I recently encountered a nice looking video encoder/decoder device by a Canadian company called Haivision, which seemed to be able to do exactly what we needed. These devices use OpenEmbedded Linux to do video streaming, so that one can take an SDI camera and stream the video over ethernet with MPEG-2 TS and decode it again on the other end.

Multicast Route Bug

Unfortunately, we found a multicast configuration bug: The unit lacks a multicast route.

The multicast route is explained in the route man page:

route add -net 224.0.0.0 netmask 240.0.0.0 dev eth0

This is an obscure one documented so people know how to do it. This sets all of the class D (multicast) IP routes to go via "eth0". This is the correct normal configuration line with a multicasting kernel.

It can be fixed easily if I could log in with SSH and add the route setup in /etc/rc.d/rc.local.

Chain Gang Software

However, after some backing and forthing with their customer support, it transpired that Haivision used a Chinese company to build the devices and that Haivision does not have the source code or the root passwords for the devices. Consequently, one can only use it for unicast streaming and multicast streaming won't work as intended.

The devices are probably good enough for the majority of users, but it is useless for our specialized application, so the devices are now in a junk box and we'll make our own solutions with general purpose embedded computers and gstreamer.

Free Software

The General Public License was intended to prevent this problem, but if people are uninformed about it, then they cannot exercise their rights.

Oh, well, what the hell!
-- The Bomber, Catch 22, by Joseph Heller

Porcupine Pi

One solution is to buy a $400 SDI to USB adaptor, plug it into a $30 Raspberry Pi computer and install Raspbian Linux operating system. A few hours of tinkering with gstreamer and we have vanilla soup.

Also see this tutorial https://www.aeronetworks.ca/2018/05/mpeg-2-transport-streams.html for complete examples on how to take MPEG-2 TS streams apart and put them back together again.

La voila!

Herman

Comments

Parasitic Quadrifilar Helical Antenna

This article was reprinted in OSCAR News, March 2018: http://www.amsat-uk.org If you want to receive Satellite Weather Pictures , then you need a decent antenna, otherwise you will receive more noise than picture. For polar orbit satellites, one needs an antenna with a mushroom shaped radiation pattern . It needs to have strong gain towards the horizon where the satellites are distant, less gain upwards where they are close and as little as possible downwards, which would be wasted and a source of noise. Most satellites are spin stabilized and therefore the antenna also needs circular polarization, otherwise the received signal will flutter as the antennas rotate through nulls. The helical antenna, first proposed by Kraus in 1948, is the natural solution to circular polarized satellite communications. It is a simple twisted wire - there seems to be nothing to it. Various papers have been published on helix antennas, so the operation is pretty well understood. Therefore,

Weather Satellite Turnstile Antennas for the 2 meter Band

NEC2, 2 m band, 146 MHz, Yagi Turnstile Simulation and Build This article describes a Turnstile Antenna for the 2 meter band, 146 MHz amateur satcom, 137 MHz NOAA and Russian Meteor weather satellites. Weather satellite reception is described here . A quadrifilar helical antenna is described here . Engineering, is the art of making what you need, from what you can get. Radiation Pattern of the Three Element Yagi-Uda Antenna Once one combine and cross two Yagis, the pattern becomes distinctly twisted. The right hand polarization actually becomes visible in the radiation pattern plot, which I found really cool. Radiation Pattern of Six Element Turnstile Antenna Only a true RF Geek can appreciate the twisted invisible inner beauty of a herring bone antenna... Six Element Turnstile Antenna Essentially, it is three crosses on a stick. The driven elements are broken in the middle at the drive points. The other elements can go straight throug

Patch Antenna Design with NEC2

The older free Numerical Electromagnetic Code version 2 (NEC2) from Lawrence Livermore Lab assumes an air dielectric. This makes it hard (but not impossible) for a radio amateur to experiment with Printed Circuit Board Patch antennas and micro strip lines. Air Spaced Patch Antenna Radiation Pattern You could use the free ASAP simulation program , which handles thin dielectrics, you could shell out a few hundred Dollars for a copy of NEC4 , You could buy GEMACS if you live in the USA, or you could add distributed capacitors to a NEC2 model with LD cards (hook up one capacitor in the middle of each element.), but that is far too much money/trouble for most. More information on driving an array antenna can be found here: https://www.aeronetworks.ca/2019/03/driving-quad-patch-array-antenna.htm l Air Dielectric Patch The obvious lazy solution is to accept the limitation and make an air dielectric patch antenna. An advantage of using air dielectric, is that the antenn

Aeronetworks sro - Airborne Linux

Search This Blog