Skip to main content

Twin Otter

If you ever visit British Columbia in Canada, then do yourself a favour and take a sight seeing trip with Harbour Air.

They operate a large fleet of old and new De Havilland seaplanes flying out of lakes and harbours all over BC - providing a delightful experience.

In this older plane, an original De Havilland, circa 1970, the upgraded turbine engine has about 50% more power, which provides seemingly effortless take-off and landings, while the cockpit is a museum piece with some essential updates.  Note the fuel flow indicator hose at the top of the panel - the ultimate in low tech!

The planes are simple and reliable aluminium sheet metal constructions, supported by Viking Air, which is continuing the De Havilland mission.  Since 2010, Viking Air builds completely new Twin Otters.

Yours truly, in the co-pilot seat.
A view of Victoria, with the snowy peaks at Vancouver in the distance.

You can literally fly from downtown Victoria, to downtown Vancouver, have a meeting and fly back again, in less time than a one way trip with BC Ferries and it won't cost you much more either.

Have fun!

Herman




Labels:

Comments

Post a Comment

On topic comments are welcome. Junk will be deleted.

Popular posts from this blog

PCB Mill

PCB Mill Kit My latest toy is a small PCB Mill, a CNC 3018 Pro, there are many available from Ali Express for the enormous sum of 285 Dirhams or so, which is about 70 Euro.  I thought that even if it didn't work at all, it would not be a big loss. Assembled CNC 3018 Kit It will help if you have a little previous workshop experience, but these machines are so simple and relatively slow moving, that any radio-geek can safely experiment. Carving With a V-bit in a Puddle of Oil Of course I can have boards made in China by Dirty PCBs , but what is the fun in that? The problem with making PCB antennas, is that you need to experiment to change the design 1 mm this way or that, to tune it just so and just such and having to wait 2 weeks for each experiment doesn't work.  A few hours playing with a router is more practical. It turned out to be a pretty nice little kit, made from aluminium and 1/4 inch Bakelite (paper reinforced phenol formaldehyde).  This Pre...
Post a Comment
Read more

Driving A 900 MHz Quad Patch Array Antenna

A Circular Polarized Quad Patch Array for the 900 MHz ISM Band Driving a patch array antenna is a tricky and multidisciplinary affair - a combination of electrics, magnetics and mechanics - where theory meets reality.  Patch antennas are useful between about 1 and 5 GHz.  Below that, they are too big and above that, too small to be practical for the manufacturing tolerances of a hobbyist.  For L, S and C-band, a radio amateur can use patches with good effect, using not much more than tin snips and a nibble tool. 902-928 MHz ISM Band LCP Quad Patch Antenna The patch antenna theory can be explored with a simulation program such as NEC2: https://www.aeronetworks.ca/2018/07/patch-antenna-design-with-nec2.html You could make an array with any number of patches, but more than four would be a whole lot of hassle.  A SAR radar antenna may have 300 tiny little patches.  However, a two by two is about the limit of my patience. Any piece of metal within half ...
4 comments
Read more

Yagi Antenna for 900 MHz ISM Band

I like tinkering with wire antenna designs, since they are simple and cheap to make.  Mr Yagi invented his antenna about 100 years ago, but there are still some things left to learn about it. 900 MHz ISM Band Yagi The 900 MHz ISM band ranges from 902 to 928 MHz.  Covering the whole band with a single Yagi antenna is difficult, since they are inherently narrow band devices.  Consequently some tweaking is required and the result below is a desensitized design that can be built and replicated quite easily, but you need a network analyzer - "To Measure, is to Know!" A Yagi generally consists of a Reflector, Radiator and one or more Director elements, arranged on a boom.  For a small Yagi, a wooden ruler works a treat, since one can easily mark the position of the wires.  The wire elements are fastened to the bottom of the ruler with hot glue.  The wire elements are  made from straightened out jumbo size paper clips.  The balun, is tw...
Post a Comment
Read more