Ethernet Funnies

Sometimes it is very hard to connect to an embedded system, because the designers cut some corners to simplify the system and keep memory use down, or simply because the system is prehistoric and full of bugs.

One such device worked fine provided that there was a little ethernet switch between the laptop machine and the target, but a direct connection between the laptop machine and target device only worked about half the time. Even the little switch sometimes could not connect.

MAC, PHY, MAG

An ethernet interface device consists of three main parts: The Media Access Controller (MAC), the Physical Interface (PHY) and a set of transformers - the Magnetics. When you plug a cable in, the PHY sends out little pulses to figure out what is going on and then swaps the wires around internally and changes the speed and duplex settings to make the interface work.

The trouble was that the target only supports 100 Mbps, while the laptop machine wanted to run at 1 Gbps and the two just could not reach agreement.

Ethtool

The ethtool program can be used to configure the ethernet interface device manually:
# ifconfig em0 up
# ethtool em0
# ethtool -s em0 speed 100 duplex full autoneg off
# ethtool em0
# ifconfig em0 192.168.111.1 netmask 255.255.255.0

That forced the laptop machine to the correct speed and duplex settings, turned the broken auto negotiation off and then life was good.

Shortly after writing the above, I ran into a case where the embedded system works better with a 100 Mbps half duplex connection, but the auto-negotiation usually resulted in a full duplex connection.

# ethtool -s em0 speed 100 duplex half autoneg off

Problem fixed.

These weird issues are usually due to a bad board layout around the ethernet chip set.

Reference

More information here:
https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/6/html/Deployment_Guide/s1-ethtool.html

La voila!

Herman

Comments

OpenEMS with Octave and SciLAB

I wanted to do some advanced RF antenna development work and needed an electromagnetic field solver that is a bit more up to date than NEC2 . Commercial solvers from Matlab , Ansys and others are hideously expensive (in the order of $20,000 to $50,000) and do not fit in the wallet of a hobbyist or a small consulting company. Recently, openEMS became available and it fills the niche with a capable free tool. In general, openEMS is a solver - a Finite-Difference Time-Domain (FDTD) numerical engine. You interact with it through Octave , which is almost identical to Matlab . You can watch a good video by Thorsten Liebig here: https://www.youtube.com/watch?app=desktop&v=ThMLf0d5gaE Getting it to work is a little painful, but it is free, so bear with it - then save a backup clone, or a zipped copy of the whole virtual machine directory and NEVER update it, to ensure that it keeps going and doesn't get broken by future updates, right when you are ...

Parasitic Quadrifilar Helical Antenna

This article was reprinted in OSCAR News, March 2018: http://www.amsat-uk.org If you want to receive Satellite Weather Pictures , then you need a decent antenna, otherwise you will receive more noise than picture. For polar orbit satellites, one needs an antenna with a mushroom shaped radiation pattern . It needs to have strong gain towards the horizon where the satellites are distant, less gain upwards where they are close and as little as possible downwards, which would be wasted and a source of noise. Most satellites are spin stabilized and therefore the antenna also needs circular polarization, otherwise the received signal will flutter as the antennas rotate through nulls. The helical antenna, first proposed by Kraus in 1948, is the natural solution to circular polarized satellite communications. It is a simple twisted wire - there seems to be nothing to it. Various papers have been published on helix antennas, so the operation is pretty well ...

Yagi Antenna for 900 MHz ISM Band

I like tinkering with wire antenna designs, since they are simple and cheap to make. Mr Yagi invented his antenna about 100 years ago, but there are still some things left to learn about it. 900 MHz ISM Band Yagi The 900 MHz ISM band ranges from 902 to 928 MHz. Covering the whole band with a single Yagi antenna is difficult, since they are inherently narrow band devices. Consequently some tweaking is required and the result below is a desensitized design that can be built and replicated quite easily, but you need a network analyzer - "To Measure, is to Know!" A Yagi generally consists of a Reflector, Radiator and one or more Director elements, arranged on a boom. For a small Yagi, a wooden ruler works a treat, since one can easily mark the position of the wires. The wire elements are fastened to the bottom of the ruler with hot glue. The wire elements are made from straightened out jumbo size paper clips. The balun, is tw...

Aeronetworks sro - Airborne Linux

Search This Blog