Skip to main content

Packet Sniffing

A Transparent Bridge

It is sometimes necessary to capture packets on a network in order to see why a certain host or device is misbehaving.

Depending on the setup, you could use Ettercap and ARP table spoofing to reroute interesting traffic to your test machine as described in another post, but usually it is best to physically insert the test machine between the unit under test and the ethernet switch as a transparent bridge and then capture or save the data using tcpdump or wireshark.

If your test machine is a laptop computer, then it likely has only one ethernet port.  You can add a second one using either a cardbus or USB ethernet adaptor.

Install the ethernet bridge utilities and create a transparent bridge br0, then assign the two ethernet ports to it (find their names with ifconfig).

Building the Bridge

Here is a bridge script that I used recently:

#! /bin/bash
echo Configure a transparent bridge for Wireshark or tcpdump.

killall NetworkManager

# Install ebtables and bridge-utils
# Ethernet ports: em1 and eth2

echo Create a transparent bridge
brctl addbr br0
brctl stp br0 off
brctl addif br0 em1
brctl addif br0 eth2

echo Enable IP4 forwarding
/sbin/ifconfig em1 0.0.0.0 promisc up
/sbin/ifconfig eth2 0.0.0.0 promisc up
echo "1" > /proc/sys/net/ipv4/ip_forward

echo The bridge IP address is 192.168.111.1
ifconfig br0 192.168.111.1 netmask 255.255.255.0 up

echo Open ebtables to allow everything, INPUT, OUTPUT and FORWARD  
iptables -F
iptables -P INPUT ACCEPT
iptables -P OUTPUT ACCEPT
iptables -P FORWARD ACCEPT
ebtables -F
ebtables -P INPUT ACCEPT
ebtables -P OUTPUT ACCEPT
ebtables -P FORWARD ACCEPT

echo Configuration:
iptables -L
ebtables -L
ifconfig


Dumping the Packets

Now you can run tcpdump on the br0 device and view or save the traffic for later analysis.  Here are a few examples:

# tcpdump -i br0
# tcpdump -nlA -i br0
# tcpdump -nlX -s 256 host 192.168.x.y and port 1234 -i br0


La voila!

Comments

Popular posts from this blog

Parasitic Quadrifilar Helical Antenna

This article was reprinted in OSCAR News, March 2018:  http://www.amsat-uk.org If you want to receive Satellite Weather Pictures , then you need a decent antenna, otherwise you will receive more noise than picture. For polar orbit satellites, one needs an antenna with a mushroom shaped radiation pattern .  It needs to have strong gain towards the horizon where the satellites are distant, less gain upwards where they are close and as little as possible downwards, which would be wasted and a source of noise.  Most satellites are spin stabilized and therefore the antenna also needs circular polarization, otherwise the received signal will flutter as the antennas rotate through nulls. The helical antenna, first proposed by Kraus in 1948, is the natural solution to circular polarized satellite communications.  It is a simple twisted wire - there seems to be nothing to it.  Various papers have been published on helix antennas, so the operation is pretty well understood. Therefore,

Patch Antenna Design with NEC2

The older free Numerical Electromagnetic Code version 2 (NEC2) from Lawrence Livermore Lab assumes an air dielectric.  This makes it hard (but not impossible) for a radio amateur to experiment with Printed Circuit Board Patch antennas and micro strip lines. Air Spaced Patch Antenna Radiation Pattern You could use the free ASAP simulation program , which handles thin dielectrics, you could shell out a few hundred Dollars for a copy of NEC4 , You could buy GEMACS if you live in the USA, or you could add distributed capacitors to a NEC2 model with LD cards (hook up one capacitor in the middle of each element.), but that is far too much money/trouble for most. More information on driving an array antenna can be found here: https://www.aeronetworks.ca/2019/03/driving-quad-patch-array-antenna.htm l Air Dielectric Patch   The obvious lazy solution is to accept the limitation and make an air dielectric patch antenna. An advantage of using air dielectric, is that the antenn

Weather Satellite Turnstile Antennas for the 2 meter Band

NEC2, 2 m band, 146 MHz, Yagi Turnstile Simulation and Build This article describes a Turnstile Antenna for the 2 meter band, 146 MHz amateur satcom, 137 MHz NOAA and Russian Meteor weather satellites.  Weather satellite reception is described here .  A quadrifilar helical antenna is described here .   Engineering, is the art of making what you need,  from what you can get. Radiation Pattern of the Three Element Yagi-Uda Antenna Once one combine and cross two Yagis, the pattern becomes distinctly twisted. The right hand polarization actually becomes visible in the radiation pattern plot, which I found really cool. Radiation Pattern of Six Element Turnstile Antenna Only a true RF Geek can appreciate the twisted invisible inner beauty of a herring bone antenna... Six Element Turnstile Antenna Essentially, it is three crosses on a stick.  The driven elements are broken in the middle at the drive points.  The other elements can go straight throug