Network connectivity - the bane of all computer users...
If I am faced with a machine with a broken network connection, I always start with a few simple tests. First see whether the machine has an IP address, netmask and default route. If the basics do not work, nothing else will, but it is amazing how many people do not think about that!
If the basics are fine, try to do a ping of another machine - that will test most things, including the Domain Name Server. Finally, I use Telnet to verify that the destination service is working.
Doing these tests manually, will provide you with helpful error messages. The Linux error messages always tell you *exactly* what the problem is. If you don't understand them, then google these messages for more information. Another unfortunate soul likely had the same problem already. If you use a GUI utility, then you are insulated from the error messages and you are reduced to aimlessly poking around in the dark.
If those do not work, try to use the Dynamic Host Configuration Protocol (DHCP) to fix things.
Doing these tests manually, will provide you with helpful error messages. The Linux error messages always tell you *exactly* what the problem is. If you don't understand them, then google these messages for more information. Another unfortunate soul likely had the same problem already. If you use a GUI utility, then you are insulated from the error messages and you are reduced to aimlessly poking around in the dark.
If those do not work, try to use the Dynamic Host Configuration Protocol (DHCP) to fix things.
ifconfig
Display the device name, IP address and netmask:
# ifconfig
em1 Link encap:Ethernet HWaddr 00:21:CC:5E:98:D9
inet addr:172.22.2.74 Bcast:172.22.2.255 Mask:255.255.255.0
inet addr:172.22.2.74 Bcast:172.22.2.255 Mask:255.255.255.0
In the olden days, the ethernet ports were always named eth0, eth1 and so on, but nowadays it seems that it can be anything at all, for example em1 or whatever the device file system chose at first startup.
You can also use ifconfig to set the IP address of an embedded system:
# ifconfig em1 192.168.0.1 netmask 255.255.255.0 up
You can also use ifconfig to set the IP address of an embedded system:
# ifconfig em1 192.168.0.1 netmask 255.255.255.0 up
route
Display the routing table and make sure that there is a default gateway defined:
# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default 172.22.2.1 0.0.0.0 UG 0 0 0 em1
172.22.2.0 * 255.255.255.0 U 1 0 0 em1
Destination Gateway Genmask Flags Metric Ref Use Iface
default 172.22.2.1 0.0.0.0 UG 0 0 0 em1
172.22.2.0 * 255.255.255.0 U 1 0 0 em1
dhclient
You can use dhclient to talk to a DHCP server to reset the machine address and route (make sure it is stopped before running it again):
# killall dhclient
# killall dhclient
# dhclient eth0
If there is no DHCP server, if for example you are running an embedded system with static addresses, then you got to configure the above manually and in this case, you should disable automatic wizards such as NetworkManager, since it will cause you periodic grief by ever so helpfully changing your static setup for you!
ping
If all works so far, try to ping something. Yahoo always answers to pings:# ping www.yahoo.com
PING ds-eu-fp3.wa1.b.yahoo.com (87.248.122.122) 56(84) bytes of data.
Some network administrators configure their routers to filter out ping requests. This is rather unhelpful, because ping is a valuable test tool, but Telnet will accomplish much the same thing.
dig
Ping also shows whether the DNS is working. If not, check the nameserver definition in /etc/resolve.conf. You can always use the Google DNS at 8.8.8.8 if you don't have a better one.You can also do a DNS test with nslookup or dig:
# dig www.yahoo.com
; <<>> DiG 9.8.4-P1-RedHat-9.8.4-3.P1.fc16 <<>> www.yahoo.com
;; global options: +cmd
;; Got answer:
;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 10032
;; flags: qr rd ra; QUERY: 1, ANSWER: 5, AUTHORITY: 0, ADDITIONAL: 0
;; QUESTION SECTION:
;www.yahoo.com. IN A
;; ANSWER SECTION:
www.yahoo.com. 0 IN CNAME fd-fp3.wg1.b.yahoo.com.
fd-fp3.wg1.b.yahoo.com. 0 IN CNAME ds-fp3.wg1.b.yahoo.com.
ds-fp3.wg1.b.yahoo.com. 0 IN CNAME ds-eu-fp3-lfb.wa1.b.yahoo.com.
ds-eu-fp3-lfb.wa1.b.yahoo.com. 0 IN CNAME ds-eu-fp3.wa1.b.yahoo.com.
ds-eu-fp3.wa1.b.yahoo.com. 42 IN A 87.248.112.181
;; Query time: 12 msec
;; SERVER: 10.10.63.5#53(10.10.63.5)
;; WHEN: Mon Apr 15 12:30:45 2013
;; MSG SIZE rcvd: 151
telnet
Finally, try to connect to the destination server using Telnet and see what it says:# telnet www.yahoo.com 80
Trying 87.248.112.181...
Connected to www.yahoo.com.
Escape character is '^]'.
You should get the web server banner and you could even GET the home page manually:
get index.html
<HEAD><TITLE>Redirect</TITLE></HEAD>
<BODY BGCOLOR="white" FGCOLOR="black">
<FONT FACE="Helvetica,Arial"><B>
"<em>http://failsafe.fp.yahoo.com/404.html</em>".<p></B></FONT>
<!-- default "Redirect" response (302) -->
</BODY>
Connection closed by foreign host.
Happy debugging!
Comments
Post a Comment
On topic comments are welcome. Junk will be deleted.